Hydrotech 5600 SE Valve Chem Free Iron Filter Operation Manu Manuel d'utilisateur télécharger pdf (Page 11)

Special Instructions for Split-Stream and Public Water Supply Installations

For a split-stream installation, a secondary pressure tank must be installed as shown in the split-stream installation

diagram (Page 4). On a public water supply installation, a pressure tank must be installed as shown in the public water

supply installation diagram (Page 4). It is recommended in both applications to use a standard air-to-water pressure tank

with an air relief valve of a capacity that would normally be installed if the water system were a standard private well.

Also note that in both applications a normally closed solenoid valve is required. Follow the standard installation

instructions above with the following additions and modifications:

1. Install the pressure tank as indicated by the appropriate diagram.

2. Install a normally closed solenoid valve after the water meter and after a line split for untreated water (if there is one).

3. On both types of installation, install the Mazzei injector between the pressure tank (secondary pressure tank on split-

stream installations) and normally closed solenoid valve.

4. Install the pressure switch after the Mazzei injector and wire it to the solenoid valve (secondary pressure switch on

split-stream installations). Set high pressure on pressure switch (which controls opening and closing of the solenoid

valve) 2 to 3 psi lower than low pressure on primary pressure switch. EXAMPLE: If primary pressure switch is set at

40-60 psi, set the secondary pressure switch at 18 to 38 psi.

5. For public water supply installations, contact your local water department or plant operator and ask what the normal

low system pressure is . Set high pressure on pressure switch 2 to 3 psi lower than this figure.

NOTE: Failure to set the pressure switch as described above will not allow proper closing of the solenoid valve

during periods of low system pressure.

Plumbing System Clean-Up

The following procedures are guidelines only but have proven successful in most instances. Under no circumstances

should any procedure outlined below be followed if contrary to the appliance manufacturer's instructions. Should there

be any questions concerning the advisability of performing a procedure, it is strongly recommended the manufacturer's

authorized service outlet be consulted prior to performing the procedure.

The plumbing system and water using appliances that have been exposed, even for a short time, to iron-fouled water

need to be cleaned of the precipitated iron that has collected in them or iron bleed (staining) will continue to be a

problem.

Depending on the amount of iron in the water and the length of time the water system has been exposed to iron fouling,

select from the following procedures those that apply to the type of system and appliances that need to be cleaned to

assure iron-free water at all points of use.

Softener

It isn't uncommon that the softener was installed in an effort to remove ferrous (clear water) iron from the water supply.

Typically a softener will remove some ferrous iron until the resin bed becomes fouled to the extent that it will lose both

hardness removal capacity and the limited capacity for iron removal. This is the condition to expect the softener to be in

when planning a system clean-up.

Prior to closing the main supply valve or turning power off to a private well system and preparatory to installing the filter

system, do the following:

1. Disconnect the brine draw line from the brine cabinet and place the loose end into a five gallon plastic pail filled with

a solution of warm water and 4 oz. of resin mineral cleaner.

2. Advance the control timer to the brine draw position (refer to instructions provided with your softener). Allow all the

warm mineral cleaner solution to be drawn into the mineral bed.

3. Then immediately close the main water supply valve or turn the power off to the pump and proceed with the filter

installation. During the time required to install the filter system, the iron-fouled softener resin will be chemically

cleaned.

4. After the filter installation is completed and final adjustments have been made, with the water turned on and the

brine draw tube reconnected, reposition the timer on the softener to the backwash position. Allow the timer to

perform an automatic regeneration cycle. During backwash of the softener, all iron cleaned from the resin will be

washed down the drain. It is advisable, after chemically cleaning the softener, to regenerate the system twice to fully

restore capacity lost due to iron-fouling.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Hydrotech 5600 SE Valve Chem Free Iron Filter Operation Manu Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Purificateurs d'eau Hydrotech 5600 SE Valve Chem Free Iron Filter Operation Manu